Sunday, November 24, 2013

Carbon in atmosphere 'could warm planet for centuries'

Global warming could continue for centuries even if carbon emissions were stopped overnight.

  A diesel particulate filter captures small soot particles,preventing
 them from being expelled into the atmosphere

Carbon dioxide which is already in our atmosphere could continue warming the planet for centuries even if new emissions were entirely halted, scientists claim.

A new analysis of future carbon emission scenarios found that it may take significantly fewer emissions for global temperatures to reach unsafe levels than previously thought.
Carbon dioxide, the most important greenhouse gas, has long-term effects because it can remain in the atmosphere for centuries after it is emitted.

To understand how long its influence on global temperatures will last, scientists produced a computer model of a scenario where all carbon emissions were immediately stopped after 1,800 billion tonnes had been released into the atmosphere.

They found that 40 per cent of the carbon would be absorbed by the oceans or landmasses within 20 years of emissions ceasing, 60 per cent within 100 years and 80 per cent within 1,000 years.

The decreasing levels of carbon in the atmosphere should in theory have a cooling effect, but this would be outweighed by the fact the oceans will absorb less and less heat as time goes on.

Previous studies had suggested that global temperatures would remain steady or decline if emissions were suddenly stopped, but did not account for the declining capacity of the oceans to continue absorbing heat, the scientists claimed.

Eventually the warming effect of heat which is no longer being absorbed by the oceans and is lingering in the atmosphere will outweigh the cooling caused by declining CO2 levels, they said.
Results published in the Nature Climate Change journal suggest that after an initial century of cooling following the stoppage of emissions, the planet would then warm by 0.37C over a 400 year period.
Although the change sounds small, it is almost half the total amount of warming seen since the start of the industrial era which stands at 0.85C.

According to the Intergovernmental Panel on Climate Change, an increase of 2C or more above pre-industrial levels could result in dangerous effects on the climate system.

Experts have previously warned that to keep global temperature rises below 2C, humans must keep the total amount of carbon dioxide emitted in the industrial era below 1,000 billion tonnes, about half of which has already been released.

But the new study suggests the 2C benchmark could be reached with significantly lower carbon emissions.
Dr Thomas Frölicher of Princeton University, who led the study, said: "If our results are correct, the total carbon emissions required to stay below two degrees of warming would have to be three-quarters of previous estimates, only 750 billion tons instead of 1,000 billion tons of carbon.

"Thus, limiting the warming to two degrees would require keeping future cumulative carbon emissions below 250 billion tons, only half of the already emitted amount of 500 billion tons."

Photo credit - Nick Collins Content Courtesy - Telegraph

Monday, November 04, 2013

Pumpkin Power: Pumpkins Can Make Renewable Electricity

According to the Department of Energy: It might not be long until the 1.4 billion pounds of pumpkins we produce annually are nearly as important to our energy security as they are to Halloween!  Thanks to the pioneering work of the East Bay Municipal Utility District (EBMUD), discarded pumpkins and other food waste are used as a source of renewable electricity. I was searching through the archives at Energy.Gov and found the following totally cool story. By Amber Archangel

Pumpkin Power: Turning Food Waste into Energy


It might not be long until the 1.4 billion pounds of pumpkins we produce annually are nearly as important to our energy security as they are to Halloween!

The story is a little different in Oakland, California. Thanks to the pioneering work of the East Bay Municipal Utility District (EBMUD), discarded pumpkins and other food waste are used as a source of renewable electricity.

What Does This Project Do?
  • Oakland’s EBMUD collect food waste and uses microbes to convert it into methane gas that is burned to generate electricity.
  • The Energy Department is helping to fund the development of integrated biorefineries, industrial centers dedicated to converting plant material into biofuels and other products.

With the passing of Halloween, millions of pounds of pumpkins have turned from seasonal decorations to trash destined for compost heaps or landfills.

How is that possible? First, waste haulers gather post-consumer food waste and deliver it to EBMUD’s anaerobic digesters. Inside these giant tanks, bacteria break down the food waste and release methane gas as a byproduct. EBMUD captures this gas and uses it to generate electricity in onsite generators. A ton of food waste provides about 367 m3 of gas, and digesting 100 tons of food wastes five days a week can generate enough electricity to power 1,000 homes. Once the food waste has been digested, the remaining solids make an excellent natural fertilizer, so they can be used to get next year’s pumpkin crop started.

Discarded pumpkins and other organic waste material can be used for more than just electricity.

The Energy Department is working together with industry to develop and test integrated biorefineries, industrial centers capable of efficiently converting plant material into affordable biofuels, biopower, and other products. These projects are located around the country and use a variety of materials as feedstocks.

Two of them, Enerkem in Mississippi and INEOS Bio in Florida, use municipal solid waste as a feedstock, like EBMUD, but use a process called gasification to produce ethanol and electricity. In 2012, INEOS Bio is planning to open the Indian River County Bioenergy Center, which will produce 8,000,000 gallons of ethanol, enough to fill about 232 of the largest railroad tank cars, and 6 megawatts of electricity a year from 300 dry tons of biomass a day, including yard waste and food scraps.

In Mississippi, Enerkem is planning a biorefinery on a regional landfill. They plan to convert 300 tons of solid waste a day into ethanol, amounting to 10,000,000 gallons (290 tank cars) of ethanol per year.

The Energy Department’s partnership with these companies is helping to remove barriers to commercialization of fuel and power production from municipal solid waste, including yard and food wastes, and so it might not be long until the 1.4 billion pounds of pumpkins we produce annually are nearly as important to our energy security as they are to Halloween!
Photo credit - Matthew Loveless Content Courtesy - Energy.Gov

Wednesday, October 30, 2013

Halloween Tips to Keep Energy Spooks Away

This Halloween, keep ghosts and goblins at bay — while saving energy and money — with these home energy efficiency tricks

In searching through the dusty archives of the Department of Energy, I found this creepy Halloween infographic. (:D) According to the Department: No need to fill your house with garlic to keep vampires at bay. Fend off these ancient creatures while saving money on lighting costs with energy-efficient light bulbs. By Amber Archangel. The following ghoulish information is from Energy.Gov:

Energy Efficiency Tricks to Stop Your Energy Bill from Haunting You This Halloween
What are the key facts?

  • The typical American family spends at least $2,000 a year on their home energy bills.
  • Families can save up to 20-30 percent on their energy bills by making energy efficiency upgrades.

It has long been said that on All Hallows’ Eve the boundary between the living world and dead thins, allowing spirits to run free.

Ghosts and goblins roam the earth, witches take to the sky on their broomsticks and vampires rise from the dead. Whether you believe in paranormal activity or not, this Halloween don’t let your energy bill give you a scare.

Defend yourself from unwanted spirits and high energy bills by sealing air leaks around windows, doors and air ducts.

Before air sealing, conduct a visual inspection to detect leaks or hire a professional for a more thorough measurement of your home’s airflow. Check out more tips to stop cold air – and Halloween spooks — from invading your home.

No need to fill your house with garlic to keep vampires at bay.

Fend off these ancient creatures while saving money on lighting costs with energy-efficient light bulbs. With traditional incandescent bulbs, about 90 percent of energy used is given off as heat. By replacing 15 inefficient incandescent bulbs with energy-saving lights, you can save about $50 per year — all while repelling vampires. Learn more about lighting choices that will save you money.

There is nothing like the crackle of a fire on a cold fall day.

But what can provide extra warmth during cooler months can also leave you vulnerable to higher energy bills and Halloween witches flying in your house. Keep warm air in your house — and witches out — with proper chimney maintenance. When not in use, be sure to close your chimney flue or use an inflatable stopper to prevent air leaks and temporarily seal the chimney.

Banish goblins and other creatures lurking in the shadows with outdoor solar lighting.

Easy to install, virtually maintenance free and with no added costs to your electric bill, outdoor solar lighting is popularly used in pathway lighting, wall-mounted lamps, freestanding lamp posts and security lights.

According to folklore, water has magical qualities, providing protection from the undead-ghosts can’t cross running water and the slightest drop causes witches to melt.

If this is a belief you ascribe to, you can stop ghosts and witches in their tracks and achieve water savings of 25-60 percent by installing low-flow fixtures. Learn how to determine if you should replace your fixtures, and be sure your faucets are equipped with an aerator to help restrict the flow of water.

Watch out for phantom loads haunting your energy bill this year.

Also called energy vampires, phantom loads refer to the energy that appliances draw when they are in standby mode, and they cost the average U.S. household $100 per year. Make phantom loads disappear by unplugging electronics and battery chargers when not in use, and be sure to explore other home electronic energy-saving tips.
This Halloween, protect yourself from evil spirits waiting to torment you — and rising energy bills — with these energy efficiency tips. After all, saving energy and money is a treat you can enjoy all year long.
Check out EnergySaver.gov for more tips on ways to save energy and money.

Infographic by : Sarah Gerrity Content Courtesy - 1sun4all

Sunday, October 06, 2013

Save Energy & Save Money Using The Sun Intelligently

One of the best ways to save money is also one of the greenest decisions we can make: that decision is the decision to save more energy. We waste a tremendous amount of energy in the US. Recent studies have found that we waste 61% to 84% of our energy in the US, and that we use 11 times more energy than the UK despite having only 5 times the population.

Energy is a huge portion of most people’s expenses. Cutting back just a bit on our energy usage could save money (tons of money) for all sorts of better things.

So, with all that on the table, what are the most effective ways to save money using the sun? I think all of the solar-related ways to save money (by saving energy) listed below are excellent solutions for the average American, but you can decide for yourself by evaluating the option as it applies to your own home or business.

Ways To Save Money With Solar Energy

Of course, as I’ve written several times here on Cost of Solar, putting solar PV panels on your roof is a pretty sure way to save tens of thousands of dollars (yep, tens of thousands). This should really be one of the first ways to save money that you should look into, especially considering that you can go solar for $0 or close to $0 down in many or most places (either through a solar leasing/PPA arrangement or through a $0 down solar loan from a bank).

But rooftop solar PV panels aren’t the only way to save energy using the sun. The below solar infographic from the Rocky Mountain Institute (RMI) shows 7 more solar-related energy saving solutions. In case you prefer text format with a bit more commentary, here’s that first:

Use Solar Light Tubes For Daylighting: Solar light tubes allow you to bring in a lot more light (cutting the need for artificial lighting, which sucks up electricity) without the installation of big windows (which leak heat in the winter and cool air from your electricity-needy air conditioner in the summer). RMI notes that the average financial payback on solar light tubes is 5 to 7 years. In itself, that’s awesome, but that doesn’t even account for the improved quality of life that comes with more daylight in your home or office.

Use Skylights: Skylights are very similar to solar light tubes, but as you can see in a basic way in the infographic, the design is a bit different. (RMI notes that the financial payback time is highly variable, so it doesn’t list a range).

Dry Your Clothes In The Sun: Here’s an old-school money-saving solution that a lot of people are moving back to. Electric dryers are energy hogs. Why suck money out of your wallet using them when you can simply let the sun dry your clothes? I’ve been using this method for the past 5 years+, but wish I had started even sooner. (Note: I started using this method when I moved to Europe, where it’s commonplace. Even in a small apartment, like mine, it’s common to set up a drying rack when you’ve got wet clothes and either set it out on the balcony or next to the window.) Of course, if you decide to jump in on this energy- and money-saving solution, the financial savings are immediate. And if you want to see how much money you’re saving, you can try comparing your electric bill to your electric bills from previous months and from the same month in previous years. I think you’ll find this is one of the most effective ways to save money (a huge chunk of it) by using the energy of the sun.

Use A Pool Cover/Blanket: If you’ve got a swimming pool, this seems like an obvious one. Get a pool blanket/cover that uses the heat from the sun to warm your pool. The financial payback time is under 1 year according to RMI.

Buy Solar Hot Water Panels For Your Pool: If you want a more high-tech and low-effort solution for heating your pool, solar hot water panels for the pool are a logical solution. Incentives for such solar panels are available in several states, and RMI projects that average financial payback time on such solar panel systems is 1.5 to 4 years. That’s an excellent payback time. And remember that you’re then saving money for decades to come (the same as making money, essentially, except you don’t have to pay taxes on financial savings!). Again, this is a “duh!” way to save money and energy that uses the tremendous energy resource of the sun rather than inefficient and harmful electricity generation from fossil fuels or heating from natural gas.

Buy Solar Hot Water Panels For Your Home: Naturally, if solar hot water panels (aka solar thermal panels) can heat your pool, they can also heat the water you use in your home. In some places I’ve visited (e.g., Malta and Crete, Greece), these solar hot water panels are on practically every roof. Again, in many states, you can get government incentives to help you purchase solar thermal panels. As the infographic below shows, solar thermal panels make a great supplement to solar PV panels. RMI notes that solar hot water panels cut 50–80% off of hot water bills, on average, and have a financial payback time of 6–10 years.

Use Solar Landscape And Patio Lighting: I’m sure you’ve seen these in home & garden shops and on many people’s lawns. You probably even have some yourself. They are one of the most logical ways to save money and energy with little initial investment. Not only do they save you money and cut your energy-related emissions, but they are also easier to relocate as your lighting needs change. You can even move them to a new home if you make a move, which is quite common these days. RMI estimates an average financial payback time of 2 years for switching to solar landscape and patio lighting.

Here’s RMI’s full infographic, Going Solar: Options For Homeowners, which also extends a bit beyond using solar energy into actually blocking solar energy in order to save money:

Yep, there are a lot of ways to save money and fossil fuel energy using the sun than RMI listed. I’m sure there are actually more than the ones above. For example, if you are a person who uses tanning beds to get a crispy tan (solariums, as they are called over here), stop throwing your money away on that and get outside to get a tan. Go to the beach, go to the bark, lay on your balcony, play a sport, go for a walk, go for a bike ride, garden, read outside… do more outside in order to stop throwing your money at a tanning salon. All of this is also better for your health, so it’s a good way to save money on healthcare and to avoid spending time at the hospital!

One more energy- and money-saving solution that comes to mind is using the sun to grow your own food. That saves tremendously on energy used to transport food around the world and to your local shop, and it also saves a good deal on the energy used to transport you to the shop to buy some food. Also, it’s a good way to save money since you aren’t putting money towards the profits grocery chains and corporate agriculture or agrindustry. Furthermore, your food will be fresher, tastier, and probably much more appreciated!

Have more ideas for ways to save money using the sun? Share them in the comments below! I’d love to be reminded of more or even learn about new ones. 

Content Courtesy - costofsolar

Sunday, September 29, 2013

Walmart: Renewable Energy-Sustainable Products-Zero Waste

Walmart reports: In front of an audience of associates, suppliers and nonprofit organizations at its Global Sustainability Milestone Meeting, Walmart highlighted on September 12, 2013, its progress with the Sustainability Index, a measurement system used to track the environmental impact of products. The company also outlined key initiatives where it can use its size and scale to help address “hot spots” and accelerate progress in supply chain sustainability. By Amber Archangel. The following is an official Walmart news release:

Walmart Highlights Progress on the Sustainability Index
Outlines key initiatives in recycling, chemicals, fertilizers and energy efficiency
Broadens Index to international markets
Index projected to include 300 product categories, engage up to 5,000 suppliers by end of year

Walmart president and CEO Mike Duke:

We’ve reached an acceleration point where we are moving from measurement to results. We’re starting to really drive progress with the Index. This is about trust and value. Using less energy, greener chemicals, fewer fertilizers and more recycled materials – all of this – is the right thing to do for the planet and it’s right for our customers and our business.



As of today, the Index has been rolled out across 200 product categories, and to more than 1,000 suppliers. By the end of this year, we expect the Index will expand to include more than 300 product categories and as many as 5,000 suppliers.
Since the Index rolled out broadly to Walmart product categories in August 2012, it has shown a consistent trend of improved product sustainability. For example, Walmart’s general merchandise department has improved its Index product sustainability score by an average of 20 percent; grocery department by an average of 12 percent; and consumables and health and wellness by an average of 6 percent.

Kara Hurst, CEO of The Sustainability Consortium: 
With the Sustainability Index, Walmart is applying the science and research that we’ve developed to create a more sustainable supply chain globally. We’re excited about the significant progress Walmart and its suppliers are making and value their partnership with us to address big issues and drive real social and environmental change.
Based on the insights and data from the Index, Walmart has been working with suppliers, nonprofits, industry experts and government to develop and implement solutions that address critical “hot spots” and opportunities across the global supply chain. As part of the progress update at today’s meeting, executives, merchants and suppliers shared progress on five major initiatives underway:

  • Increasing the Use of Recycled Materials. More than 29 million tons of valuable plastics are sent to landfills every year in the U.S. at a cost of about $6.6 billion annually. Walmart aims to grow both the supply and demand for recycled plastics so they can be diverted from landfill and get a second life. The company is working with cities to increase plastic recycling and with suppliers to increase the use of recycled content and make packaging more recyclable. Changes in packaging are already being implemented in product categories such as beverage, over-the-counter drugs, dairy creamers and berry containers. 
Earlier this week, Walmart and Sam’s Club also announced a smartphone trade-in program in the U.S. that goes into effect on Sept. 21.

The company will not send these trade-ins to landfills, domestically or internationally, potentially saving hundreds of thousands of smartphones from landfills annually.

  • Offering Products with Greener Chemicals. Walmart provided an overview of its new Consumables Chemicals initiative, describing how it is working with suppliers to reduce or eliminate the use of priority chemicals used in consumables products in favor of greener alternatives. It will begin with household cleaning, personal care, beauty and cosmetic products, asking suppliers to transition to greener substitutes for priority chemicals.


In addition, starting in Jan. 2014, Walmart will begin to label its private brand cleaning products in accordance with the U.S. Environmental Protection Agency’s recommended Design for the Environment (DfE) Safer Product Labeling program, and will continue to assess the applicability of DfE as Walmart expands it to broader product areas.

  • Reducing Fertilizer Use in Agriculture. Walmart is requiring suppliers who use commodity grains, such as corn, wheat and soy in their products, to develop a fertilizer optimization plan that outlines clear goals to improve performance based on Index research. Through this program, the company and its suppliers have the potential to reduce fertilizer use on 14 million acres of farmland in the U.S. by 2020.
  • Expanding the Sustainability Index to International Markets. Walmart will expand the Sustainability Index and measurement to international markets with the goal of improving product sustainability at the global level. Walmart Chile and Walmart Mexico will launch the Index in their respective markets in 2014. In addition, South Africa’s Massmart has begun to include key Index questions in its supplier sustainability surveys.
  • Improving Energy Efficiency. The Index has uncovered the importance of energy efficiency in several product categories, such as televisions, plastic toys, small appliances and greeting cards. By working with suppliers to improve energy efficiency through the supply chain of these products, Index energy scores have already improved 23 percent in general merchandise categories. Walmart is now providing tools for suppliers to help track and reduce the energy used to produce these products.
The company also announced a light-emitting diode (LED) lightbulb available in stores now under its Great Value label.
A 40 watt equivalent bulb, which last more than twice as long as a compact fluorescent lightbulb (CFL), typically retails for $8.48 and the 60 watt equivalent $9.88. By selling 500,000 LED lightbulbs, the company projects customers can save more than $67 million over the lifetime of those bulbs.
Content Courtesy - 1sun4all

Thursday, September 19, 2013

The Clean Energy Revolution Is Happening-Now!

For decades, America has chased after the promise of clean, domestic energy, reports Energy.gov. But even as costs fell and technology matured, that clean energy future seemed to linger just beyond our reach. Critics often said this new world would “always be five years away.” Today, that is changing. By Amber Archangel


Energy.gov note: This article originally appeared on WhiteHouse.gov
#Cleantechnow: Learn More

  • Watch a video featuring Secretary Moniz that highlights four key energy technologies that have already made America’s clean energy future a reality.
  • Read the full “Revolution Now” report.
  • Use the tag #CleanTechNow to share photos on Twitter, Instagram or via email newmedia@hq.doe.gov how clean energy technology already plays a role in your daily life. We’ll feature our favorite submissions on Energy.gov next week.

In recent years, costs for numerous critical clean energy technologies-wind power, solar panels, super energy-efficient LED lights and electric vehicles-have fallen significantly.

The accompanying surge in deployment has been truly spectacular. Such a surge is tantamount to topping the barricades — a level of cost reduction and market penetration that will enable a full scale clean energy revolution in the relatively near term. A new Department of Energy report, “Revolution Now: the Future Arrives for Four Clean Energy Technologies” documents this transformation and what it means for America’s energy economy. The clean technology revolution is upon us.


While these technologies still represent a small percentage of their respective markets, that share is expanding at a rapid pace and influencing markets.

For instance:


  • In 2012, wind was America’s largest source of new electrical capacity, accounting for 43 percent of all new installations. Altogether the United States has deployed about 60 gigawatts of wind power — enough to power 15 million homes.
  • Since 2008, the price of solar panels has fallen by 75 percent, and solar installations have multiplied tenfold. Many major homebuilders are incorporating rooftop panels as a standard feature on new homes.
  • In that same five years, the cost of super-efficient LED lights has fallen more than 85 percent and sales have skyrocketed. In 2009, there were fewer than 400,000 LED lights installed in the U.S., today, the number has grown 50-fold to almost 20 million.
  • During the first six months of 2013, America bought twice as many plug-in electric vehicles(EVs) as in the first half of 2012, and six times as many as in the first half of 2011. In fact, the market for plug-in electric vehicles has grown much faster than the early market for hybrids. Today, EVs ranging from the Chevy Volt to the Tesla Model S also boast some of the highest consumer satisfaction ratings in America. And prices are falling and export markets are opening up. Since 2008, the cost of electric vehicle batteries — which really drive the economics of EVs — has dropped by 50 percent.

As these new markets continue to expand, so will the challenges and opportunities associated with transforming America’ energy system. Already increased energy efficiency and distributed solar energy are posing challenges to traditional utility business models. America will have to invest in building a smarter, more robust and resilient electrical grid with an extensive network of EV chargers and new approaches to consumer bills. These challenges are in fact emblematic of success for America’s clean energy markets.

Since 2008, the price of solar panels has fallen by 75 percent, and solar installations have multiplied tenfold.

But why are these clean energy markets growing so fast? Policy plays an important role — and not just for renewables. For instance, from 1980 to 2002, the federal government’s production incentives for unconventional natural gas laid a foundation for that sector’s dramatic rise. Today, time-limited tax credits for wind, solar and electric vehicles, in concert with technology and manufacturing advances, are stimulating a similar market expansion.


Of course, these are also great products that bring real benefits to consumers.

For example, no one likes the hassle of repeatedly buying and replacing incandescent light bulbs. A mother who installs a quality LED fixture when her child is born will not need to replace it until that child goes to college — or even graduates. By that time, each LED light she installs will have saved her about $140 in electricity costs. By 2030, LED lights will save Americans $30 billion a year on energy alone.


Forty years ago, an oil embargo sparked panic, rationing and fuel lines across America. But today, Americans can declare their independence from oil, skip the gas lines and recharge at home for the equivalent of about $1.22 a gallon – as opposed to $3.56 for gasoline. We call this low-cost electric fuel an eGallon, and — depending on where you live — eGallon savings can be quite compelling. For instance, in Washington State a gallon of gasoline is almost $4, but the equivalent eGallon costs only 85 cents because of clean, low-cost electricity.

These market revolutions are enabled by robust private-public partnerships for research, development, demonstration and deployment — including some sizable investments from the Energy Department. And this Administration’s Climate Action Plan, which calls for commonsense steps to reduce carbon pollution and address the effects of climate change, will further accelerate the development and diffusion of these, and other, transformative energy technologies.

Today, we can finally say with confidence that America is witnessing the shift to a cleaner, more domestic and more secure energy future. It is not a faraway goal.


Photo credit - Raymond David . Content Courtesy - 1sun4all

Thursday, August 08, 2013

Energy-Efficient Windows Inspired By Nature : New Bio-Inspired Approach To Thermal Cooling Could Be Applied To Solar Panels


A. Schematic of the composite window structure. B. The artificial vascular network layer.”

A new type of energy-efficient window — inspired by and recreating the vascular networks found within living organisms — has been created by researchers at the University of Toronto. The new windows work effectively to limit heat loss during the winter and provide a cooling effect during the summer. The new design has resulted in 7–9 degrees of cooling in laboratory experiments. The researchers also think that their new technique/design could be applied to solar panels, working to increase their functional efficiency thanks to the cooling effect.

The new process is, in the words of the researchers themselves, a “bio-inspired approach to thermal control for cooling (or heating) building window surfaces,” one that works through the action of optically clear, flexible, elastomer sheets, which are attached and bonded to normal glass window panes. The attached elastomer sheets — which are composed of polydimethylsiloxane (PDMS) — feature ‘channels’ through which room-temperature water is free to flow. It’s this flowing water that provides the thermal controlling effects.

“Our results show that an artificial vascular network within a transparent layer, composed of channels on the micrometer to millimeter scale, and extending over the surface of a window, offers an additional and novel cooling mechanism for building windows and a new thermal control tool for building design,” stated Ben Hatton, lead researcher and a professor of engineering at the University of Toronto.

As the researchers note, windows currently account for around 40% of all building energy costs — any improvements with regard to their thermal regulatory abilities would be valuable. Hatton continued: “In contrast to man-made thermal control systems, living organisms have evolved an entirely different and highly efficient mechanism to control temperature that is based on the design of internal vascular networks. For example, blood vessels dilate to increase blood flow close to the skin surface to increase convective heat transfer, whereas they constrict and limit flow when our skin is exposed to cold.”

As Hatton notes — the new technique could probably very effectively be applied to solar panels, and could also function well as a means of supplying heated water to existing hot water or heat storage systems.

The new research was just published in the journal Solar Energy Materials & Solar Cells.
Photo credit - University of Toronto Faculty of Applied Science & Engineering
Content Courtesy -cleantechnica

Sunday, August 04, 2013

Greenhouse Gas Emissions Explained, in 7 Balloons



In 2010 human activity caused 50 Gt CO2e of greenhouse gas emissions.

These emissions were 76% carbon dioxide (CO2), 16% methane (CH4), 8% nitrous oxide (N20) and 2% F-gases.

The big terrestrial emitters were China (23%), the USA (14%), Europe (10%), India (5%) and Russia (5%).

And the primary sources of emissions were energy (35%), industry (18%), transport (13%), agriculture (11%), forestry (11%), buildings (8%) and waste (4%).

The sources are explained in more detail in the balloons above, which technically shouldn’t float so well ;-).  These balloons don’t look very threatening, but they represent the large majority of positive climate forcings.

Which in English means they are major causes of climate change.

Check out our new eBook for ideas that will deflate your balloon.

Photo credit - shrinkthatfootprint Content Courtesy - shrinkthatfootprint.com

Monday, July 15, 2013

Urban Regeneration and Climate-friendly Development: Lessons from Japan

As part of their research within the United Nations University Institute of Advanced Studies (UNU-IAS) Sustainable Urban Futures Programme, Postdoctoral Fellow Osman Balaban and Assistant Director/Senior Research Fellow Jose Antonio Puppim de Oliveira examine the potential role of urban regeneration in climate change mitigation and adaptation.



Cities have a central role to play in tackling climate change as well as in adapting to its effects as they contribute much to it and are under severe threat from its impacts. Because urban spatial policies have long-term effects, they are key for tackling climate change and it is through such policies that city governments can guide climate-friendly planning.

Spatial policies cover a range of issues from a regional scale to individual buildings, including promotion of compact cities, provision of green spaces and water bodies (retention and detention ponds, water canals, etc.), retrofitting existing buildings, infrastructure renewal, and increasing non-motorized and public transport coverage. They may further be useful in achieving climate change mitigation and adaptation goals simultaneously. For instance, green spaces mitigate emissions through carbon sequestration and help combat impacts like heat stress, air pollution and flooding.

Introduction of such spatial policies necessitates certain forms of intervention in existing urban areas. “Urban regeneration” inherently comprises such interventions, from renewal to rehabilitation, and thus can provide opportunities to introduce spatial policies that address climate change.

However, urban regeneration research has so far focused on community-based issues, governance aspects and even sustainability, but not much attention has been paid to climate change. With our recent paper we intended to contribute to the literature by enhancing understanding of the potential role of urban regeneration in climate change mitigation and adaptation.

We undertook a close examination of how and with what effect different forms of policy responses to climate change are emerging in urban areas. We also examined how and to what extent urban regeneration, as a major field and instrument of urban policymaking, could be linked with these policy responses and thus turned into a city-based response to climate change.

The research was based on two case studies in Japan where the focus of urban planning has shifted from growth to reorganization that is designed to create compact cities in the country’s era of depopulation. There are recent attempts to convert existing regeneration sites into smart districts, where carbon emissions and environmental footprints are lowered. However, further research that strengthens the links between urban regeneration and climate change is required to foment the scale-up of these initiatives.

Urban regeneration evolves

Urban regeneration is a way to reorganize and upgrade existing built environments rather than planning new urbanization. It is an old concept that has evolved over time. Its roots can be traced back to the 1970s when many cities in Britain and the United States started initiatives, referred to as “urban renewal” or “area improvement”, that focused on physical renewal of inner cities identified as “areas of social deprivation”.

By the late 1970s, economic aspects like revitalization of downtown cores or entire cities were incorporated into renewal schemes and urban regeneration became a more comprehensive concept. Property-led urban regeneration projects dominated urban policymaking in British and US cities in the 1980s, based on the understanding that a supply of new premises for office, industrial and retail activities would facilitate local economic transformation. These projects came as part of the strategies to achieve the “entrepreneurial city”, a new form of urban governance to encourage local economic development.

Nevertheless, the ineffectiveness of the property-led approach in addressing issues of social equity and environmental protection led to incorporation of new goals into the urban regeneration concept. During the 1990s, the environmental benefits of improving existing urban areas were recognized and regeneration projects began to be considered as a means of addressing the three pillars of sustainability: economic revitalization, social justice and environmental protection.

There have been recent attempts to associate urban regeneration with climate policy, but these remain in their infancy and require further efforts to improve their theoretical and practical underpinnings. Current progress is limited to a few examples of regeneration projects that are designed to contribute to climate change mitigation and adaptation along with other objectives.

The regeneration process entails different forms of spatial interventions which could change the form and land use structure of cities in a way that could facilitate the implementation of spatial policies that address climate change.

Perhaps the most fruitful form of intervention is effective utilization of inner-city lands. Through urban regeneration, city governments can make the best use of brownfields and underutilized lands, providing the possibility of employing a “grow-in” strategy to concentrate the majority of new developments in existing urban areas, in the form of mixed-use developments.

Such a strategy may help achieve energy and resource efficiency by preventing urban sprawl and, in particular, reducing commuting time and distance. Further, less energy is consumed in compact cities for urban infrastructure operations. We know that 30 percent of urban energy consumption goes to pumping water and collecting wastewater. So, the more area that a city occupies, the higher the amount of energy used in that city to provide water to and collect wastewater from buildings.

Buildings are among the major sources of carbon emissions due to energy consumption for heating and cooling. Further, poor quality buildings and those sited in disaster-vulnerable (eg., on floodplains) areas are the most vulnerable to climate impacts. In many nations, buildings that will be in use in the next decades are already built. Special attention should therefore be paid to turning existing buildings into low-carbon and less vulnerable structures. Urban regeneration could help in overcoming such building-related challenges, either by retrofitting or renewing existing buildings, as part of the renewal and rehabilitation of inner cities.

Urban regeneration in Japan

Japan has been depopulating since 2005 and, according to projections by Tetsuo Kidokoro, the population of cities of all sizes will start to decrease after 2015. Due to this demographic change, the focus of urban planning and development in Japan has shifted from growth to reorganization. More attention is now paid to turning cities into more compact and sustainable places with a high quality of life.

This could be done by addressing urban problems inherited from a previous period of rapid urbanization, such as urban sprawl, decline in city centres and disaster vulnerability. Further, in line with global and national environmental concerns, greenhouse gas emissions in Japanese cities have to be lowered.

Much can be expected from urban regeneration in transforming Japanese cities into more sustainable and low-carbon urban environments in the era of depopulation. We looked at two urban regeneration initiatives in Japan, representing two major approaches of regeneration practices in Japanese cities, namely “project-based” and “plan-based” approaches.

The first case was the Minato Mirai 21 project (MM21) located in the central quarter of Yokohama City in the Tokyo Metropolitan Area.  Although initiated in the mid-1980s, the project is still in progress. MM21 was built on 186 hectares of brownfields and reclaimed lands and is currently a mixed-use district, including offices, malls, residences, hotels, cultural centres, a hospital and parks. The main objective of the project is to increase the self-sufficiency of Yokohama by strengthening its central business district.

The second case was Kanazawa City in Ishikawa prefecture in eastern Japan — a mid-sized historical town with a population of 462,361 people. Kanazawa has been encountering problems caused by urban sprawl, such as decline in the city centre, high reliance on automobiles and an increase in carbon emissions. Since the 1990s, the city government has been addressing these problems through several means, including urban regeneration. The “City Center Revitalization Plan”, which covers an area of 860 hectares and includes actions to regenerate the city center, is the primary component of urban regeneration attempts in Kanazawa.

We analysed the impacts of these two initiatives to tackle climate change by breaking them down by the following aspects: economy and work, buildings and land use, transportation and mobility, infrastructure for resource efficiency, energy consumption and efficiency, and community-based issues.

In addition to the scope and extent of their climate benefits, both cases presented a series of lessons on transforming urban regeneration projects into opportunities to reorganize cities in climate-friendly manners as described below.

Flexibility in project conception and design

Flexibility in the design of regeneration projects can help to incorporate them with new concepts that emerge over time. A main feature of the MM21 project is the delay in its completion due to the economic recession in the 1990s.

Slow realization of the project turned out to be an opportunity to eliminate the shortcomings in project design regarding environmental issues. Contemporary concepts like waste recycling, green buildings and smart grids — that did not exist at the time when the project was initiated — began to be incorporated into the project over time. Further, as the project has not yet been fully implemented, city government has had the opportunity to apply new environmental technologies to turn MM21 into a smart district. MM21 is one of the major “Yokohama Smart City Project” areas.

Participation and political commitment

Although community participation is important, it cannot guarantee a climate-friendly and low-carbon city. In the Kanazawa case, where varied stakeholders are involved in decision-making, the overall impacts of the plan have been relatively minor. This is mainly due to the main actors’ weak political commitment and lack of resources to pursue climate change mitigation and adaptation.

Therefore, in order to benefit from community engagement, participation mechanisms need to be supported with political commitment and the two should complement each other. Only then can a balance between technical top-down and participatory bottom-up approaches be achieved throughout regeneration practices.
Coordination between city divisions and policies

A sectoral approach dominates policymaking in both cities. Different city administration divisions are in charge of different sectors regarding urban development and environmental management. However, coordination between them seems to be insufficient. For instance, the Waterworks Bureau of Yokohama City takes no particular action on water issues directly related to climate change, as a separate division of the city government is in charge of global warming and climate change.

Considering a similar problem, Kanazawa’s environmental plan draws attention to the need for effective coordination between city divisions to facilitate the implementation of environmental strategies. For instance, Ishikawa prefecture has developed an “Eco-House Project” to raise citizens’ awareness of green buildings and encourage them to install green technologies in their houses. However, lessons from this prefectural project seem to have not been reflected in Kanazawa’s City Center Revitalization Plan.

Binding and structural measures

A main factor that limited the positive impacts of the revitalization plan in Kanazawa is the reluctance of the city’s government to introduce binding measures. Instead, it chose to adopt “soft” measures aiming to achieve behavioral change in the long-run. For instance, the plan avoids restricting car use, although it aims at decreasing the use of private cars for inner-city trips.

Such an approach seems to have prevented the plan from being supported by strong and complimentary measures. Likewise, the limited capacity of the city government to introduce structural measures in certain policy fields resulted in similar outcomes. As Kanazawa’s bus system is run by the private sector, the city government couldn’t introduce structural regulations on the system, and soft policies have been ineffective in overcoming the structural deficiencies in the system. This illustrates that binding and structural measures should be introduced as part of regeneration projects, particularly to ensure compliance and behavioral change.

The crosscutting potential

Our case studies demonstrated that urban regeneration is an instrument of urban policy that has the potential to facilitate the introduction of spatial policies to address climate change.Interventions inherent to the regeneration process could be used to upgrade existing urban environments and hence change the form and land use structure of cities in climate-friendly manners.

As a crosscutting field of urban policy, urban regeneration could also help in bridging the “mitigation and adaptation dichotomy” and create synergies between two major targets of climate policy, helping to achieve mitigation and adaptation goals simultaneously. In the MM21 project, adaptation actions like provision of green spaces and infrastructure improvements have been implemented together with mitigation actions like a district heating and cooling system.

Of course, achieving this is not straightforward and hindered by multiple challenges, as noted above. Overall, there remains the need to understand conceptually, and in practice, how urban regeneration could help to both tackle climate change and achieve its main objectives of revitalizing certain areas in the urban fabric.

Photo credit - Minato Mirai 21, Yokohama, Japan. Photo: Marc Antomattei. Content Courtesy - UNU.edu



Saturday, June 08, 2013

Today is World Oceans Day

Make the Ocean Promise



June 8th is World Oceans Day! On World Oceans Day, people around the planet celebrate and honor the body of water which links us all, for what it provides humans and what it represents. Be a part of this growing global celebration! Make your promise now via the World Oceans Day website @ http://bit.ly/ocean_promise

Tuesday, June 04, 2013

Celebrating World Environment Day on 5 June 2013


Think.Eat.Save.



The theme for this year’s World Environment Day celebrations is Think.Eat.Save. Think.Eat.Save is an anti-food waste and food loss UNEP - United Nations Environment Programme campaign that encourages you to reduce your foodprint. 

According to the UN Food and Agriculture Organization (FAO), every year 1.3 billion tonnes of food is wasted. This is equivalent to the same amount produced in the whole of sub-Saharan Africa. At the same time, 1 in every 7 people in the world go to bed hungry and more than 20,000 children under the age of 5 die daily from hunger. 

Given this enormous imbalance in lifestyles and the resultant devastating effects on the environment, this year’s theme – Think.Eat.Save – encourages you to become more aware of the environmental impact of the food choices you make and empowers you to make informed decisions. While the planet is struggling to provide us with enough resources to sustain its 7 billion people (growing to 9 billion by 2050), FAO estimates that a third of global food production is either wasted or lost. 

Food waste is an enormous drain on natural resources and a contributor to negative environmental impacts. This year’s campaign rallies you to take action from your home and then witness the power of collective decisions you and others have made to reduce food waste, save money, minimize the environmental impact of food production and force food production processes to become more efficient. If food is wasted, it means that all the resources and inputs used in the production of all the food are also lost. 

For example, it takes about 1,000 litres of water to produce 1 litre of milk and about 16,000 litres goes into a cow’s food to make a hamburger. The resulting greenhouse gas emissions from the cows themselves, and throughout the food supply chain, all end up in vain when we waste food. In fact, the global food production occupies 25% of all habitable land and is responsible for 70% of fresh water consumption, 80% of deforestation, and 30% of greenhouse gas emissions. It is the largest single driver of biodiversity loss and land-use change. 

Making informed decision therefore means, for example, that you purposefully select foods that have less of an environmental impact, such as organic foods that do not use chemicals in the production process. Choosing to buy locally can also mean that foods are not flown halfway across the world and therefore limit emissions. So think before you eat and help save our environment! Know more at http://www.unep.org/wed/

Wednesday, April 24, 2013

Hard to Stomach: Two Billion Now Overweight

Mark Notaras confirms beyond doubt, that what was once viewed as a problem in Western societies, is now and will increasingly be a global one.

“The share of adults worldwide who are overweight jumped from 1.45 billion in 2002 to 1.934 billion in 2010, an increase of 25 percent.” If this opening sentence of the recent Vital Signs Online report from the Worldwatch Institute is not alarming enough, of even more concern is that the world is inevitably heading further down the track of an obesity epidemic.

In other words, rather than overweightness correlating specifically to a geographic region or certain cultural groups (think of the stereotypical “fat American”, once the butt of all jokes), the strongest causal factor is increased income, and the high calorie, meat-based, fast-food dependent “Western” diet, as well as lifestyle factors that accompany it.

With tens of millions of people joining the global middle class year on year, particularly in the fast growing economies of the BRICS (Brazil, Russia, India, China, South Africa), it can be expected that the number of people with expanded waistlines will also swell, unless significant policy and behavioural changes occur.

In India for example, a country generally associated with a low-impact vegetarian diet, roughly one in five adults (19%) are now considered overweight, up from 14% in 2002. This in a country of 1.2 billion people and home to the greatest number of the world’s hungry — a figure, incidentally, that rose by 65 million from 1990 to 2005 according to a recent Oxfam report.

Overweight versus Obese

Overweightness can generally be divided into two categories — “overweight” and “obese”. In their report, Worldwatch classify “overweight” as referring to people with a body mass index (BMI) — a measure relating to a person’s height to weight ratio — of 25 or greater. If a person is obese, he or she would have a BMI of 30 or above. For the sake of this article, “overweight” refers to people in both categories, and “adult” refers to people surveyed over the age 15 from a total of 177 countries.


The global picture of obesity drawn from UN Population Division data and analysed by geographer Richard H. Weil, clearly points to a correlation of income with BMI across all regions.

While the global trend of higher income equals higher BMI is clear, there are some variations at the country level. Excluding 20 poor countries with low BMI located in Asia and Africa because they include large populations suffering from malnutrition, Japan (23%) is somewhat of an anomaly. At almost 19 percentage points better than the next (sizeable) ranked industrialised country, France (42%), Japan’s highly urbanised population have managed to draw enough from their traditional food culture (of rice, soybeans, fish and vegetables) to stay healthy.

Not surprisingly, Japan’s high health standards are reflected in the Japanese definition of obesity itself, which refers to people with BMI levels over 25 (and not the universal 30). But even the revered Japanese will be concerned at their longer terms trends towards higher meat consumption, not least because of their increasingly reliance on imported foods.

Broadly speaking, high income countries — from the United States (79%) to Australia (71.1%) to Qatar (62.7%) to Brunei (61.7%) — have high levels of average BMI regardless of which region of the world they are in.

Weighing up the Consequences

Of course, being overweight or obese is not merely an aesthetic concern for individuals and their families, friends and colleagues. Resultant health consequences like diabetes and heart disease impact on people’s quality of life and their ability to carry out day-to-day functions. And when aggregated across populations at a country and increasingly global level, overeating has monumental impacts on the health of our environmental assets.

Raj Patel has captured these impacts in his book "Stuffed and Starved" that talks about the ironies of a world in which the number of people going hungry (approximately 1 billion) is only eclipsed by the number of people overeating.

Even though the American Heart Association recommends that moderately active adults eat around 2,500 (male) or 2,000 (female) calories per day respectively, the average American is currently stuffing themselves with 3770 calories per person per day. Other figures from the 2010 FAO Statistical Yearbook on “Dietary energy protein and fat consumption" indicate that comparable countries include Austria (3760) and Greece (3700).

All of this unnecessary consumption is having significant consequences on Earth’s already stretched land, water and soil resources.This is not to say that every overweight person is taking food straight out of the mouths of a malnourished person. The international food trade is more complex than that. However, the world’s poorest people are more likely than ever to be competing for their staple sources of calories, e.g. for corn and wheat crops, against increasing demands for biofuels and livestock feed, not to mention food market speculators. And as can be expected in any market situation where the weakest lack protection, the world’s poor farmers are coming off second best.

Incidentally, increasing awareness about the global overeating epidemic comes at a time when global hunger continues to be in the spotlight due to the onset of drought affecting millions in East Africa and continuing high world food prices. In relation to the latter, the Food Price Index measured by the Food and Agriculture Organisation of the United Nations indicate that, despite drops in commodity values for certain major crops like sugar, the overall level of food prices remains at near-record highs.

The Beginning (or the End) of Overeating

So, is there any positive news from this latest research? As the report is keen to point out, experience from Japan and other countries that illustrate higher disposable incomes do not necessarily lead to unbalanced food and leisure choices and subsequently obesity, offer some hope.

It is important to bear in mind that genetic factors also account for how well different populations adapt to high-impact diets and lifestyle changes driven by urbanisation. These differences are most stark in the Oceania region where there are large discrepancies between Polynesian and Micronesian countries on the one hand (a staggering 88% overweight) and Melanesian countries like Papua New Guinea with relatively low levels of BMI.

Still, Oceania, a region of many small island states and a very small combined population, can hardly be a template for the world. Neither, it is hoped, is the US. Former US Food and Drug Administration Commissioner (1990–1997) Dr. David A Kessler outlines a positive plan for Americans to “stop the vicious and unhealthy cycle of overeating” in his 2009 book "The End of Overeating: Taking Control of the Insatiable American Appetite".

Yet the bottom line is that, even if the US or any other developed country more accustomed to dealing with obesity can overcome the natural tendencies of people to consume fatty, salty and sugary food, at a global level, the era of overeating is probably only just beginning.

Mark Notaras is a writer/editor for the United Nations University (UNU) Media Studio and a researcher for the UNU Institute for Sustainability and Peace (UNU-ISP).